How To Prioritize Wifi On Windows 10

On Windows 10, if you accept a device with more than one network adapter (such as Ethernet and Wi-Fi), each interface receives a priority value automatically based on its network metric, which defines the primary connectedness that your device will use to send and receive networking traffic.

Although, for the about role, Windows 10 does a pretty proficient job selecting an optimal connexion to admission the network, sometimes yous may need to configure the order of the network adapters manually. For example, if you lot want to employ a Wi-Fi over an Ethernet interface when both adapters are connected to the network.

You could disable those adapters you don't utilise, but it may not be the best solution as you may need them as backups. Instead, a more than straightforward solution is to adjust the interface metric to specify in which order your device should employ each network adapter, which you can exercise using Control Console and PowerShell.

In this Windows 10 guide, nosotros'll walk you lot through the steps to alter the network adapter priorities to stay continued using your prefered adapter when using multiple interfaces.

How to alter network adapter priorities using Control Panel
How to alter network adapter priorities using PowerShell

How to change network adapter priorities using Control Panel

If you want to change the social club in which Windows 10 uses network adapters, do the following:

Open Settings.
Click on Network & Net.
Click on Status.
Click the Change Adapter options detail.
Right-click the network adapter yous want to prioritize, and select Properties.
Select the Internet Protocol Version 4 (TCP/IPv4) particular.
Click the Properties button.
In the "General" tab, click the Avant-garde button.
Clear the Automatic metric choice.
In the "Interface metric" field assign a priority value for the adapter.

Quick Tip: The lower the metric number means higher priority, and a college number indicates lower priority.
Click the OK button.
Click the OK button again.
Click the Close button.

Once you've completed the steps, Windows 10 will prioritize the network traffic depending on your configuration.

The merely caveat using the Command Panel feel is that depending on your network setup, you lot may need to adjust the metric for the Internet Protocol Version 6 (TCP/IPv6) every bit well, if that's the protocol you're using. (Unremarkably, yous volition be using the TCP/IPv4 protocol.)

At any fourth dimension, y'all can revert the changes using the same instructions, just on pace No. 9, make sure to check the Automated metric option.

How to change network adapter priorities using PowerShell

Alternatively, you can change network adapters priorities on a device with multiple interfaces using PowerShell with these steps:

Open up Start.
Search for Windows PowerShell, correct-click the top issue a select Run as administrator.
Type the post-obit command to identify the current interface metric and interface alphabetize number and press Enter:

Get-NetIPInterface
Type the following control to change the priority lodge of the network adapter and printing Enter:

Set-NetIPInterface -InterfaceIndex 21 -InterfaceMetric 10

In the command, make sure to modify the -InterfaceIndex value to reflect the network adapter you want to prioritize and change the -InterfaceMetric value to assign a priority. As well, remember that a lower metric number means college priority, and a college metric number means lower priority.
Type the following command to see the new metric applied to the network adapter and press Enter:

Get-NetIPInterface

After completing the steps, Windows ten will prioritize the network traffic depending on your configuration when multiple network adapters are connected to the network.

At any time, y'all can go back to the previous behavior assuasive Windows ten to decide the network adapter priority using these steps:

Open Starting time.
Search for Windows PowerShell, right-click the tiptop result a select Run as administrator.
Type the post-obit command to place the current interface metric and interface index number and printing Enter:

Set-NetIPInterface -InterfaceIndex 21 -AutomaticMetric enabled

In the command, brand sure to change the -InterfaceIndex value with the correct number of the network adapter you want to apply an automatic metric.

More Windows x resource

For more helpful articles, coverage, and answers to mutual questions near Windows 10, visit the following resources:

Windows 10 on Windows Central – All y'all need to know
Windows 10 help, tips, and tricks
Windows 10 forums on Windows Central

Buyer's guide

The Dell XPS 15 is our choice for best 15-inch laptop

For a lot of people, a 15-inch laptop is a perfect size that offers enough screen for multitasking, and in a lot of cases, some extra functioning from powerful hardware. We've rounded upwardly the all-time of the best at this size.

Mojang Studios needs to come clean about Minecraft on Xbox Series X|S

Kill the suspense

Mojang Studios needs to come clean nearly Minecraft on Xbox Serial X|S

Minecraft players have been eagerly awaiting a "current-gen" upgrade for Minecraft on Xbox Serial X|S since the consoles launched, especially for the possibility of ray tracing. After the contempo mishap with mistakenly released prototype code, information technology's fourth dimension for Mojang Studios to come clean. What'south going on?